Investigation of Weld Characteristics of Stainless Steel Material Fabricated by TIG Welding Process: A Review
DOI:
https://doi.org/10.61841/msktb279Keywords:
TIG, SS4l0, SS04L, Arc welding, ManufacturingAbstract
The welding process for SS410 metal by using TIG welding voltage, gas flow rate, and strike-off distance were selected to ascertain with effect on the metal hardness of the welding bed. The NDT technique is used to detect the welding bed. SS410 has gathered wide acceptance in the fabrication of light-weight structures requiring a high strength-to-weight ratio and good corrosion resistance. Modern structures concept demand reduction in the weight as the cost of production and fabrication of the material 410 SS joints are inevitable for certain application due to unique performances such as corrosion resistance and mechanical properties the process welding parameters like current voltage gas flow rate of TIG for getting maximum weldment and best mechanical properties the analysis of the test result is conducted using a welding parameter range that, given best result, found this combination can be considered a good range for TIG welding of SS410 material and conduct the study of temperature distribution and total heat flux of welding area using the analysis. The scope of arc welding has to be increased in the various engineering field like aerospace nuclear and under water industries where complex geometry and hazardous environments necessitate fully automated systems. Even traditional application of arc welding, such as off-highway and automotive manufacturing, have to be increased due to their demand in quality cost accuracy and volume to stay competitive As a result, process parameter are needed to improve the existing process weld
Downloads
References
1. Kumar S. (2010). Experimental investigation on pulsed TIG welding of aluminum plate. Advanced
Engineering Technology
2. Indira Rani, M., & Marpu, R. N. (2012). Effect of Pulsed Current TIG Welding Parameters on Mechanical
Properties of J-Joint Strength of Aa6351. The International Journal of Engineering and Science (IJES)
3. Almazrouee T.Shehata S.Oraby Effect of Welding Parameters on the Weld Bead Geometry of Low Alloy
Steel using FCAW Empirical Modeling Approach International Journal of Mining, Metallurgy &
Mechanical Engineering (IJMMME) Volume 3, Issue 3 (2015) ISSN 2320-4060 (Online)
4. Sudhakaran. Ra*, Sivasakthivel. P Sb Nagaraja Sc., And Eazhil. K.M 12th global congress on
manufacturing AND MANAGEMENT, GCMM 2014
5. Ahmed Khalid Hussain, Abdul Lateef, Mohd Javed Prames [2010] " Influence of
Welding Speed on Tensile Strength of Welded Joint in TIG Welding Process", International
Journal Of Applied Engineering Research, Volume 1, No. 3
6. Arun Narayanan Cijo Mathew Vinod Yeldo Baby, Joby Joseph [2013] "Influence of Gas Tungsten Arc
Welding Parameters in ALUMINIUM 5083 Alloy", International Journal of Engineering Science and
Innovative Technology (IJESIT) Vol. 2, Issue 5
7. Palani Pk Saju M (2013) optimization process parameters for TIG welding of ALUMINIUM 65032
international journal research application VOL 3,230-236
8. Indira rani 2012 effect of pulsed current TIG welding parameters on mechanical properties of j joint
strength of AA6351, the international journal engineering and science
9. N.Karunakaran V.Balasubramanian 2010 effect of puled current on gas tungsten arc weld Aluminium
alloy joint journal of science direct SP 21,278-286
10. Paravinder Singh, Experimental Investigation of Deposition rate of TIG Welding of Grade 316 Stainless
Steel, International Journal of Engineering Science & Advanced Technology 4(3) (2014), 257-262.
11. Paravinder Singh Rajinder Singh, Experimental Investigation of Deposition Rate in TIG Welding of
Grade, 304 Stainless Steel,
12. Radha raman International Journal of Advanced Engineering Technology (2014) The yield strength of
dissimilar joint of SS 202 and mild steel is best for both TIG and MIG welding processes.
13. The dissimilar metal joint of SS 304 and mild steel has poor ultimate tensile stress for both TIG and MIG
welding processes.
14. Priya Cgauhan Hemant Panchal, May 2016 Ijsdr Vol 1 Issue 5: A Review on Activated Gas Tungsten
ARC Welding (A-GTAW).
15. T. Sandor, Janos Materials Science For Vols. 537-538 (2007), pp. 63-70: The experiences activated tungsten
inert gas (A-TIG) welding applied on 1.4301 type stainless steel plates
16. J Modensi, Eustaquio R. Apolinario And M. Pereira, “TIG welding with single component fluxes,” Journal
of Materials Processing Technology, vol.99 (1–3) pp. 260–266, 2000
17. Chavda S. P. Desai, J. V. And Patel T. M. 2014. A review on optimization of MIG welding parameter using TAGUCHI DOE method. International Journal of Engineering and Management Research, Vol. 4, pp. 16-21.
18. Deva kumar D. And Jabaraj D. B. 2014. Research on gas tungsten arc welding of stainless steel-An
overview International Journal of Scientific & Engineering Research. Vol. pp 1612-1618.
19. Mishra Raman Radha Tiwari Kumar Vishnu And Rajesha S- 2014. A study of tensile strength of MIG
and TIG welded dissimilar joints of mild steel and stainless steel. International Journal of Advances in
Materials Science and Engineering (IJAMSE) Vol.3, No.2, April 201412. Ravinder Jarial S.K-2015.
Parameter optimization of TIG welding on SS-202 and Mild Steel by using Taguchi Method International
Journal of Enhanced Research in Science Technology & Engineering, ISSN: 2319-7463Vol. 4 Issue 6,
June-201513. Bharwal Shail, Vyas Charit-2014.
20. Weldability Issue of AISI 202 SS (Stainless Steel) Grade with GTAW Process Compared to AISI 304 SS
Grade. International Journal of Advanced Mechanical Engineering. ISSN 2250-3234 Volume4, Number
6 (2014), pp. 695-700
21. Howse D.S And Lucas W Investigation into arc constriction by active fluxes for tungsten inert gas
welding,” Science and Technology of Welding and Joining, vol.5 (3), pp.189–193,2000
22. B..ramesh kumar weld quality analysis of tig laser and electron beam welded ss304 and 316 material with
NDT technique proceeding and the national seminar & exhibition on non destructive evaluation NDE
Chennai 2011,pp346-349
23. Siddharaj prajapati ketan shah vol 2 issue 3 2016 experimental study on activated tungsten inert gas
welding
24. Lgardner 2005 the use of stainless steel in structures prog struct engng meter vol 7 pp 48-55
25. Paulo j modenesi eustaquio r.apolinario and laci m.pereira TIG welding with single component fluxes
journal of material processing technology vol.99(13) pp 260 266,2000
26. kuang hung tseng and ko juli chuang,study of type 316l stainless steel TIG welding with mo03 powder
advanced material research vol 291-294
27. Pk saju 2013 optimization of process parameter for TIG welding of aluminium 65032 international journal
engineering research vol 3,230-236.
28. PN.rao-manufacturing technology –mcgraw hill education 2013
29. Randhawa were carried out effect of a TIG welding process parameter on penetration in mild steel plate
30. J..niagaj were carried out peculiarities of TIG welding of titanium and its alloy
31. E.ahmadi A.R Ibrahim were carried out the effect of activating fluxes on 316l stainless steel weld joint
characteristics in TIG welding using the taguchi method
32. Syarul asraf mohmat were carried out the effect of flux core arc welding fcaw process on different
parameters
33. Cheng hsien kuo were carried out effect of activated TIG flux on performance dissimilar weld between
mild steel and stainless steel
34. Samarad were carried out influences of the activating flux on weld joint properties at arc stud welding
process
35. Michael liu were carried out a TIG welding of titanium plate using cryolite containing flux pastes and flux cored wires
Downloads
Published
Issue
Section
License
Copyright (c) 2020 AUTHOR
This work is licensed under a Creative Commons Attribution 4.0 International License.
You are free to:
- Share — copy and redistribute the material in any medium or format for any purpose, even commercially.
- Adapt — remix, transform, and build upon the material for any purpose, even commercially.
- The licensor cannot revoke these freedoms as long as you follow the license terms.
Under the following terms:
- Attribution — You must give appropriate credit , provide a link to the license, and indicate if changes were made . You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use.
- No additional restrictions — You may not apply legal terms or technological measures that legally restrict others from doing anything the license permits.
Notices:
You do not have to comply with the license for elements of the material in the public domain or where your use is permitted by an applicable exception or limitation .
No warranties are given. The license may not give you all of the permissions necessary for your intended use. For example, other rights such as publicity, privacy, or moral rights may limit how you use the material.
