Experimental Analysis of a Self-Homogenization of the Fuel Spray in the 3d-Pm Engine

Authors

  • Arun V Rejus Kumar Assistant Professor, Department of Mechanical Engineering, BIST, BIHER, Bharath Institute of Higher Education & Research, Selaiyur, Chennai Author
  • A. Sagai Francis Britto Research Scholar, DST- JRF (INSPIRE Fellow), Department of Mechanical Engineering, BIST, BIHER, Bharath Institute of Higher Education & Research, Selaiyur, Chennai. Author

DOI:

https://doi.org/10.61841/4b3fgh46

Keywords:

Experimental Analysis, Self-Homogenization, 3d-Pm Engine

Abstract

 The advantages of homogeneous combustion in internal combustion (I.C.) engines are well known and many research groups all over the world are working on its practical realization. Recently, the present authors have proposed a new combustion concept that fulfils all requirements to perform homogeneous combustion in I.C. engines using the Porous Medium Combustion Engine, called “PM -engine”. This is an I.C. engine with the following processes realized in a porous medium: internal heat recuperation, fuel injection and vaporization, mixing with air, homogenization, 3 Dthermal self-ignition followed by a homogeneous combustion. Figure 1 shows the simplest case of the operation of a PM-engine, where the PM-combustion chamber is mounted in engine head. During the intake stroke it is weak influence of the PM-heat capacitor on the in-cylinder air thermodynamic conditions. Heat exchange process (nonadiabatic compression) increases with continuing compression, and at the TDC the whole combustion air is closed in the PM volume. Near the TDC of compression the fuel is injected in to PM volume and very fast fuel vaporization and mixing with air occur in 3D-structure of PM-engine. The selfignition process and homogeneous combustion occur in PM volume close to the TDC 

Downloads

Download data is not yet available.

References

[1] Thooyamani, K.P., Khanaa, V., & Udayakumar, R. (2014). Virtual instrumentation based process of

agriculture by automation. Middle-East Journal of Scientific Research, 20(12): 2604-2612.

[2] Udayakumar, R., Kaliyamurthie, K.P., & Khanaa, T.K. (2014). Data mining a boon: Predictive system for

university topper women in academia. World Applied Sciences Journal, 29(14): 86-90.

[3] Anbuselvi, S., Rebecca, L.J., Kumar, M.S., & Senthilvelan, T. (2012). GC-MS study of phytochemicals in

black gram using two different organic manures. J Chem Pharm Res., 4, 1246-1250.

[4] Subramanian, A.P., Jaganathan, S.K., Manikandan, A., Pandiaraj, K.N., Gomathi, N., & Supriyanto, E.

(2016). Recent trends in nano-based drug delivery systems for efficient delivery of phytochemicals in

chemotherapy. RSC Advances, 6(54), 48294-48314.

[5] Thooyamani, K.P., Khanaa, V., & Udayakumar, R. (2014). Partial encryption and partial inference control

based disclosure in effective cost cloud. Middle-East Journal of Scientific Research, 20(12), 2456-2459.

[6] Lingeswaran, K., Prasad Karamcheti, S.S., Gopikrishnan, M., & Ramu, G. (2014). Preparation and

characterization of chemical bath deposited cds thin film for solar cell. Middle-East Journal of Scientific

Research, 20(7), 812-814.

[7] Maruthamani, D., Vadivel, S., Kumaravel, M., Saravanakumar, B., Paul, B., Dhar, S.S., Manikandan, A., &

Ramadoss, G. (2017). Fine cutting edge shaped Bi2O3rods/reduced graphene oxide (RGO) composite for

supercapacitor and visible-light photocatalytic applications. Journal of colloid and interface science, 498,

449-459.

[8] Gopalakrishnan, K., Sundeep Aanand, J., & Udayakumar, R. (2014). Electrical properties of doped

azopolyester. Middle-East Journal of Scientific Research, 20(11). 1402-1412.

[9] Subhashree, A.R., Parameaswari, P.J., Shanthi, B., Revathy, C., & Parijatham, B.O. (2012). The reference

intervals for the haematological parameters in healthy adult population of chennai, southern India. Journal

of Clinical and Diagnostic Research: JCDR, 6(10), 1675-1680.

[10] Niranjan, U., Subramanyam, R.B.V., & Khanaa, V. (2010, September). Developing a web recommendation

system based on closed sequential patterns. In International Conference on Advances in Information and

Communication Technologies, 101, 171-179. Springer, Berlin, Heidelberg.

[11] Slimani, Y., Baykal, A., & Manikandan, A. (2018). Effect of Cr3+ substitution on AC susceptibility of Ba

hexaferrite nanoparticles. Journal of Magnetism and Magnetic Materials, 458, 204-212.

[12] Premkumar, S., Ramu, G., Gunasekaran, S., & Baskar, D. (2014). Solar industrial process heating associated

with thermal energy storage for feed water heating. Middle East Journal of Scientific Research, 20(11),

1686-1688.

[13] Kumar, S.S., Karrunakaran, C.M., Rao, M.R.K., & Balasubramanian, M.P. (2011). Inhibitory effects of

Indigofera aspalathoides on 20-methylcholanthrene-induced chemical carcinogenesis in rats. Journal of

carcinogenesis, 10.

[14] Beula Devamalar, P.M., Thulasi Bai, V., & Srivatsa, S.K. (2009). Design and architecture of real time webcentric tele health diabetes diagnosis expert system. International Journal of Medical Engineering and

Informatics, 1(3), 307-317.

[15] Ravichandran, A.T., Srinivas, J., Karthick, R., Manikandan, A., & Baykal, A. (2018). Facile combustion

synthesis, structural, morphological, optical and antibacterial studies of Bi1− xAlxFeO3 (0.0≤ x≤ 0.15)

nanoparticles. Ceramics International, 44(11), 13247-13252.

[16] Thovhogi, N., Park, E., Manikandan, E., Maaza, M., & Gurib-Fakim, A. (2016). Physical properties of CdO

nanoparticles synthesized by green chemistry via Hibiscus Sabdariffa flower extract. Journal of Alloys and

Compounds, 655, 314-320.

[17] Thooyamani, K.P., Khanaa, V., & Udayakumar, R. (2014). Wide area wireless networks-IETF. Middle-East

Journal of Scientific Research, 20(12), 2042-2046.

[18] Sundar Raj, M., Saravanan, T., & Srinivasan, V. (2014). Design of silicon-carbide based cascaded

multilevel inverter. Middle-East Journal of Scientific Research, 20(12), 1785- 1791.

[19] Achudhan, M., Jayakumar M.P. (2014). Mathematical modeling and control of an electrically-heated

catalyst. International Journal of Applied Engineering Research, 9(23), 23013.

[20] Thooyamani, K.P., Khanaa, V., & Udayakumar, R. (2013). Application of pattern recognition for farsi

license plate recognition. Middle-East Journal of Scientific Research, 18(12), 1768-1774.

[21] Jebaraj, S., Iniyan S. (2006). Renewable energy programmes in India. International Journal of Global

Energy Issues, 26(43528), 232-257.

[22] Sharmila, S., & Jeyanthi Rebecca, L. (2013). Md Saduzzaman., Biodegradation of domestic effluent using

different solvent extracts of Murraya koenigii. J Chem and Pharm Res, 5(2), 279-282.

[23] Asiri, S., Sertkol, M., Guner, S., Gungunes, H., Batoo, K.M., Saleh, T.A., Manikandan A., & Baykal, A.

(2018). Hydrothermal synthesis of CoyZnyMn1-2yFe2O4 nanoferrites: magneto-optical

investigation. Ceramics International, 44(5), 5751-5759.

[24] Rani, A.J., & Mythili, S.V. (2014). Study on total antioxidant status in relation to oxidative stress in type 2

diabetes mellitus. Journal of clinical and diagnostic research: JCDR, 8(3), 108-110.

[25] Karthik, B. (2014). Arulselvi, Noise removal using mixtures of projected gaussian scale mixtures. MiddleEast Journal of Scientific Research, 20(12), 2335-2340.

[26] Karthik, B., Arulselvi, & Selvaraj, A. (2014). Test data compression architecture for low power VLSI

testing. Middle - East Journal of Scientific Research, 20(12), 2331-2334.

[27] Vijayaragavan, S.P., Karthik, B., & Kiran Kumar, T.V.U. (2014). Privacy conscious screening framework

for frequently moving objects. Middle-East Journal of Scientific Research, 20(8), 1000-1005.

[28] Kaliyamurthie, K.P., Parameswari, D., & Udayakumar, R. (2013). QOS aware privacy preserving location

monitoring in wireless sensor network. Indian Journal of Science and Technology, 6(5), 4648-4652.

[29] Silambarasu, A., Manikandan, A., & Balakrishnan, K. (2017). Room-temperature superparamagnetism and

enhanced photocatalytic activity of magnetically reusable spinel ZnFe 2 O 4 nanocatalysts. Journal of

Superconductivity and Novel Magnetism, 30(9), 2631-2640.

[30] Jasmin, M., Vigneshwaran, T., & Beulah Hemalatha, S. (2015). Design of power aware on chip embedded

memory based FSM encoding in FPGA. International Journal of Applied Engineering Research, 10(2),

4487-4496.

[31] Philomina, S., & Karthik, B. (2014). Wi-Fi energy meter implementation using embedded linux in ARM

9. Middle-East Journal of Scientific Research, 20, 2434-2438.

[32] Vijayaragavan, S.P., Karthik, B., & Kiran Kumar, T.V.U. (2014). A DFIG based wind generation system

with unbalanced stator and grid condition. Middle-East Journal of Scientific Research, 20(8), 913-917.

[33] Rajakumari, S.B., & Nalini, C. (2014). An efficient data mining dataset preparation using aggregation in

relational database. Indian Journal of Science and Technology, 7, 44-46.

[34] Karthik, B., Kiran Kumar, T.V.U., Vijayaragavan, P., & Bharath Kumaran, E. (2013). Design of a digital

PLL using 0.35 μm CMOS technology. Middle-East Journal of Scientific Research, 18(12), 1803-1806.

[35] Sudhakara, P., Jagadeesh, D., Wang, Y., Prasad, C.V., Devi, A.K., Balakrishnan, G., Kim B.S., & Song, J.I.

(2013). Fabrication of Borassus fruit lignocellulose fiber/PP composites and comparison with jute, sisal and

coir fibers. Carbohydrate polymers, 98(1), 1002-1010.

[36] Kanniga, E., & Sundararajan, M. (2011). Modelling and characterization of DCO using pass transistors.

In Future Intelligent Information Systems, 86(1), 451-457. Springer, Berlin, Heidelberg.

[37] Sachithanandam, P., Meikandaan, T.P., & Srividya, T. Steel framed multi storey residential building

analysis and design. International Journal of Applied Engineering Research, 9(22), 5527-5529.

[38] Kaliyamurthie, K.P., Udayakumar, R., Parameswari, D., & Mugunthan, S.N. (2013). Highly secured online

voting system over network. Indian Journal of Science and Technology, 6(S6), 4831-4836.

[39] Sathyaseelan, B., Manikandan, E., Lakshmanan, V., Baskaran, I., Sivakumar, K., Ladchumananandasivam,

R., Kennedy, J., & Maaza, M. (2016). Structural, optical and morphological properties of post-growth

calcined TiO2 nanopowder for opto-electronic device application: Ex-situ studies. Journal of Alloys and

Compounds, 671, 486-492.

[40] Saravanan, T., Sundar Raj M., & Gopalakrishnan K. (2014). SMES technology, SMES and facts system,

applications, advantages and technical limitations. Middle - East Journal of Scientific Research, 20(11),

1353-1358.

[41] Sofiazizi, A., & Kianfar, F. (2015). Modeling and Forecasting Exchange Rates Using Econometric Models

and Neural Networks. International Academic Journal of Innovative Research, 2(4), 11-27.

[42] Singh, S.P. (2014). Security Configuration and Performance Analysis of FTP Server. International Journal

of Communication and Computer Technologies, 2(2), 106-109.

[43] Bindu, M.V. (2018). Enhancement of Thermal Performance of Solar Parabolic Trough ConcentratorTechniques- Review. Bonfring International Journal of Industrial Engineering and Management Science,

9(3), 16-20.

[44] Nandhini, P., Vijayasharathy, G., Kokila, N.S., Kousalya, S., & Kousika, T. (2016). An Improved Approach

of DWT and ANC Algorithm for Removal of ECG Artifacts. International Journal of Communication and

Computer Technologies, 4(2), 82-87.

[45] Devi, G. (2016). High Speed Image Searching for Human Gait Feature Selection. International Journal of

Communication and Computer Technologies, 4(2), 88-95.

[46] Suba, R. And Satheeskumar, R. (2016). Efficient Cluster Based Congestion Control in Wireless Mesh

Network. International Journal of Communication and Computer Technologies, 4(2), 96-101.

[47] Amiri, M., & Akkasi, A. (2015). Assessing security challenges in online social networks. International

Academic Journal of Science and Engineering, 2(4), 1-10.

[48] Loganya, R., Lavanya, S., Logasangeerani, S., & Thiruveni, M. (2014). Low Power VLSI Architecture

forReconfigurable FIR Filter. International Journal of System Design and Information Processing, 2(2), 30-

33.

[49] Kiruthika, S., Dhivya, T., & Kiruthika, S.S. (2018). Performance Analysis of Faculty and Students Using

Neo 4j. Bonfring International Journal of Networking Technologies and Applications, 5(1), 3-5.

[50] KuthsiyatJahan, S., Chandru, K., Dhanapriyan, B., Kishore Kumar, R., and Vinothraj, G. (2017). SEPIC

Converter based Water Driven Pumping System by Using BLDC Motor. Bonfring International Journal of

Power Systems and Integrated Circuits, 7(1), 7-12.

Downloads

Published

31.10.2019

How to Cite

Rejus Kumar, A. V., & Francis Britto, A. S. (2019). Experimental Analysis of a Self-Homogenization of the Fuel Spray in the 3d-Pm Engine. International Journal of Psychosocial Rehabilitation, 23(4), 300-313. https://doi.org/10.61841/4b3fgh46