Preparation and Performance Analysis of CI Engine Run by Blends of Diesel and Biodiesel (Karanja Oil)

Authors

  • V. Jose Ananth Vino Assistant Professor, Department of Mechanical Engineering, BIST, BIHER, Bharath Institute of Higher Education & Research, Selaiyur, Chennai Author
  • Ashish Patel UG Scholar, Department of Mechanical Engineering, BIST, BIHER, Bharath Institute of Higher Education & Research, Selaiyur, Chennai. Author
  • Arun Kumar UG Scholar, Department of Mechanical Engineering, BIST, BIHER, Bharath Institute of Higher Education & Research, Selaiyur, Chennai. Author
  • Abhishek Kumar UG Scholar, Department of Mechanical Engineering, BIST, BIHER, Bharath Institute of Higher Education & Research, Selaiyur, Chennai. Author
  • Ajay Yadav UG Scholar, Department of Mechanical Engineering, BIST, BIHER, Bharath Institute of Higher Education & Research, Selaiyur, Chennai. Author

DOI:

https://doi.org/10.61841/qx2bhv13

Keywords:

Diesel and Biodiesel, Performance Analysis, CI Engine

Abstract

Biodiesel is an alternative fuel to diesel and is described as a fatty acid methyl ester from vegetable oil or animal fats. The main objective of our project is to reduce the higher viscosity of Karanja oil by transesterification and to increase the performance and emission characteristics of diesel engines. By using the biodiesel from pun gam oil, the performance test of the biodiesel blend (B00, B10, B20) in 1500 rpm and a 5 bhp mechanically loaded CI engine is tested. By using different blends, we have identified the engine parameters such as brake thermal efficiency, specific fuel consumption, total fuel consumption, and brake power. In this, finally, we have determined which blend is better and which consumes less fuel. Biodiesel has the distinct advantages of being a renewable, biodegradable, & eco-friendly fuel. During the recent years, in the field of alternative fuels, especially in the area of biodiesel, research has been extensively carried out, and different samples of biodiesel have been prepared considering the scope, availability, and economics of various edible and non-edible oils. Biodiesel from Mahua, Linseed, Rice Bran, Waste Cooking Oil, Crude Palm, Castor, Jatropha, & Karanja has already been prepared and successfully tested in diesel engines & vehicles. Small capacity reactors of 5 & 10 liters of biodiesel were designed and developed also for experimental purposes. As per the Ministry of Rural Development, the National Mission on Biodiesel is proposed to be implemented in two phases. The first phase will involve a demonstration stage for the plantation of jatropha on four lakh hectares and associated research activities for establishing the commercial viability of the fuel. Phase two will involve self-sustaining expansion of the biodiesel program. The overall objective of the national mission is to promote the creation of national infrastructure for production of biodiesel through cultivation of the jatropha plant and processing of its oil. 

Downloads

Download data is not yet available.

References

[1] Thooyamani, K.P., Khanaa, V., & Udayakumar, R. (2014). Virtual instrumentation based process of

agriculture by automation. Middle-East Journal of Scientific Research, 20(12): 2604-2612.

[2] Udayakumar, R., Kaliyamurthie, K.P., & Khanaa, T.K. (2014). Data mining a boon: Predictive system for

university topper women in academia. World Applied Sciences Journal, 29(14): 86-90.

[3] Anbuselvi, S., Rebecca, L.J., Kumar, M.S., & Senthilvelan, T. (2012). GC-MS study of phytochemicals in

black gram using two different organic manures. J Chem Pharm Res., 4, 1246-1250.

[4] Subramanian, A.P., Jaganathan, S.K., Manikandan, A., Pandiaraj, K.N., Gomathi, N., & Supriyanto, E.

(2016). Recent trends in nano-based drug delivery systems for efficient delivery of phytochemicals in

chemotherapy. RSC Advances, 6(54), 48294-48314.

[5] Thooyamani, K.P., Khanaa, V., & Udayakumar, R. (2014). Partial encryption and partial inference control

based disclosure in effective cost cloud. Middle-East Journal of Scientific Research, 20(12), 2456-2459.

[6] Lingeswaran, K., Prasad Karamcheti, S.S., Gopikrishnan, M., & Ramu, G. (2014). Preparation and

characterization of chemical bath deposited cds thin film for solar cell. Middle-East Journal of Scientific

Research, 20(7), 812-814.

[7] Maruthamani, D., Vadivel, S., Kumaravel, M., Saravanakumar, B., Paul, B., Dhar, S.S., Manikandan, A., &

Ramadoss, G. (2017). Fine cutting edge shaped Bi2O3rods/reduced graphene oxide (RGO) composite for supercapacitor and visible-light photocatalytic applications. Journal of colloid and interface science, 498,

449-459.

[8] Gopalakrishnan, K., Sundeep Aanand, J., & Udayakumar, R. (2014). Electrical properties of doped

azopolyester. Middle-East Journal of Scientific Research, 20(11). 1402-1412.

[9] Subhashree, A.R., Parameaswari, P.J., Shanthi, B., Revathy, C., & Parijatham, B.O. (2012). The reference

intervals for the haematological parameters in healthy adult population of chennai, southern India. Journal

of Clinical and Diagnostic Research: JCDR, 6(10), 1675-1680.

[10] Niranjan, U., Subramanyam, R.B.V., & Khanaa, V. (2010, September). Developing a web recommendation

system based on closed sequential patterns. In International Conference on Advances in Information and

Communication Technologies, 101, 171-179. Springer, Berlin, Heidelberg.

[11] Slimani, Y., Baykal, A., & Manikandan, A. (2018). Effect of Cr3+ substitution on AC susceptibility of Ba

hexaferrite nanoparticles. Journal of Magnetism and Magnetic Materials, 458, 204-212.

[12] Premkumar, S., Ramu, G., Gunasekaran, S., & Baskar, D. (2014). Solar industrial process heating

associated with thermal energy storage for feed water heating. Middle East Journal of Scientific

Research, 20(11), 1686-1688.

[13] Kumar, S.S., Karrunakaran, C.M., Rao, M.R.K., & Balasubramanian, M.P. (2011). Inhibitory effects of

Indigofera aspalathoides on 20-methylcholanthrene-induced chemical carcinogenesis in rats. Journal of

carcinogenesis, 10.

[14] Beula Devamalar, P.M., Thulasi Bai, V., & Srivatsa, S.K. (2009). Design and architecture of real time webcentric tele health diabetes diagnosis expert system. International Journal of Medical Engineering and

Informatics, 1(3), 307-317.

[15] Ravichandran, A.T., Srinivas, J., Karthick, R., Manikandan, A., & Baykal, A. (2018). Facile combustion

synthesis, structural, morphological, optical and antibacterial studies of Bi1− xAlxFeO3 (0.0≤ x≤ 0.15)

nanoparticles. Ceramics International, 44(11), 13247-13252.

[16] Thovhogi, N., Park, E., Manikandan, E., Maaza, M., & Gurib-Fakim, A. (2016). Physical properties of

CdO nanoparticles synthesized by green chemistry via Hibiscus Sabdariffa flower extract. Journal of Alloys

and Compounds, 655, 314-320.

[17] Thooyamani, K.P., Khanaa, V., & Udayakumar, R. (2014). Wide area wireless networks-IETF. MiddleEast Journal of Scientific Research, 20(12), 2042-2046.

[18] Sundar Raj, M., Saravanan, T., & Srinivasan, V. (2014). Design of silicon-carbide based cascaded

multilevel inverter. Middle-East Journal of Scientific Research, 20(12), 1785- 1791.

[19] Achudhan, M., Jayakumar M.P. (2014). Mathematical modeling and control of an electrically-heated

catalyst. International Journal of Applied Engineering Research, 9(23), 23013.

[20] Thooyamani, K.P., Khanaa, V., & Udayakumar, R. (2013). Application of pattern recognition for farsi

license plate recognition. Middle-East Journal of Scientific Research, 18(12), 1768-1774.

[21] Jebaraj, S., Iniyan S. (2006). Renewable energy programmes in India. International Journal of Global

Energy Issues, 26(43528), 232-257.

[22] Sharmila, S., & Jeyanthi Rebecca, L. (2013). Md Saduzzaman., Biodegradation of domestic effluent using

different solvent extracts of Murraya koenigii. J Chem and Pharm Res, 5(2), 279-282.

[23] Asiri, S., Sertkol, M., Guner, S., Gungunes, H., Batoo, K.M., Saleh, T.A., Manikandan A., & Baykal, A.

(2018). Hydrothermal synthesis of CoyZnyMn1-2yFe2O4 nanoferrites: magneto-optical

investigation. Ceramics International, 44(5), 5751-5759.

[24] Rani, A.J., & Mythili, S.V. (2014). Study on total antioxidant status in relation to oxidative stress in type 2

diabetes mellitus. Journal of clinical and diagnostic research: JCDR, 8(3), 108-110.

[25] Karthik, B. (2014). Arulselvi, Noise removal using mixtures of projected gaussian scale mixtures. MiddleEast Journal of Scientific Research, 20(12), 2335-2340.

[26] Karthik, B., Arulselvi, & Selvaraj, A. (2014). Test data compression architecture for low power VLSI

testing. Middle - East Journal of Scientific Research, 20(12), 2331-2334.

[27] Vijayaragavan, S.P., Karthik, B., & Kiran Kumar, T.V.U. (2014). Privacy conscious screening framework

for frequently moving objects. Middle-East Journal of Scientific Research, 20(8), 1000-1005.

[28] Kaliyamurthie, K.P., Parameswari, D., & Udayakumar, R. (2013). QOS aware privacy preserving location

monitoring in wireless sensor network. Indian Journal of Science and Technology, 6(5), 4648-4652.

[29] Silambarasu, A., Manikandan, A., & Balakrishnan, K. (2017). Room-temperature superparamagnetism and

enhanced photocatalytic activity of magnetically reusable spinel ZnFe 2 O 4 nanocatalysts. Journal of

Superconductivity and Novel Magnetism, 30(9), 2631-2640.

[30] Jasmin, M., Vigneshwaran, T., & Beulah Hemalatha, S. (2015). Design of power aware on chip embedded

memory based FSM encoding in FPGA. International Journal of Applied Engineering Research, 10(2),

4487-4496.

[31] Philomina, S., & Karthik, B. (2014). Wi-Fi energy meter implementation using embedded linux in ARM

9. Middle-East Journal of Scientific Research, 20, 2434-2438.

[32] Vijayaragavan, S.P., Karthik, B., & Kiran Kumar, T.V.U. (2014). A DFIG based wind generation system

with unbalanced stator and grid condition. Middle-East Journal of Scientific Research, 20(8), 913-917.

[33] Rajakumari, S.B., & Nalini, C. (2014). An efficient data mining dataset preparation using aggregation in

relational database. Indian Journal of Science and Technology, 7, 44-46.

[34] Karthik, B., Kiran Kumar, T.V.U., Vijayaragavan, P., & Bharath Kumaran, E. (2013). Design of a digital

PLL using 0.35 μm CMOS technology. Middle-East Journal of Scientific Research, 18(12), 1803-1806.

[35] Sudhakara, P., Jagadeesh, D., Wang, Y., Prasad, C.V., Devi, A.K., Balakrishnan, G., Kim B.S., & Song, J.I.

(2013). Fabrication of Borassus fruit lignocellulose fiber/PP composites and comparison with jute, sisal and

coir fibers. Carbohydrate polymers, 98(1), 1002-1010.

[36] Kanniga, E., & Sundararajan, M. (2011). Modelling and characterization of DCO using pass transistors.

In Future Intelligent Information Systems, 86(1), 451-457. Springer, Berlin, Heidelberg.

[37] Sachithanandam, P., Meikandaan, T.P., & Srividya, T. Steel framed multi storey residential building

analysis and design. International Journal of Applied Engineering Research, 9(22), 5527-5529.

[38] Kaliyamurthie, K.P., Udayakumar, R., Parameswari, D., & Mugunthan, S.N. (2013). Highly secured online

voting system over network. Indian Journal of Science and Technology, 6(S6), 4831-4836.

[39] Sathyaseelan, B., Manikandan, E., Lakshmanan, V., Baskaran, I., Sivakumar, K., Ladchumananandasivam,

R., Kennedy, J., & Maaza, M. (2016). Structural, optical and morphological properties of post-growth

calcined TiO2 nanopowder for opto-electronic device application: Ex-situ studies. Journal of Alloys and

Compounds, 671, 486-492.

[40] Saravanan, T., Sundar Raj M., & Gopalakrishnan K. (2014). SMES technology, SMES and facts system,

applications, advantages and technical limitations. Middle - East Journal of Scientific Research, 20(11),

1353-1358.

[41] Sumangala, K. (2019). A Smart System for Indoor Plant Care. Journal of Computational Information

Systems, 15(1), 61-64.

[42] Satheeshkumar, R. (2019). Real Time Virtual Human Hand for Robotics. Journal of Computational

Information Systems, 15(1), 82-89.

[43] Santhosh kumar, K. (2019). A Systematic Review on Finger Vein Recognition Techniques Based on

Template Matching. Journal of Computational Information Systems, 15(1), 114-122.

[44] Priyadharshini, M., & Amsaveni, R. (2015). Case Based Automatic Text Classification Using Semantic

Relationship. International Journal of Advances in Engineering and Emerging Technology, 7(9), 586-596.

[45] Sivakumar, R., & Dr. Duraisamy, S. (2015). Designing a Novel Framework of Load Balancing Cluster with

Target Coverage Problem and Trust Evaluation for Military Wireless Sensor Networks. International

Journal of Advances in Engineering and Emerging Technology, 7(9), 597-614.

[46] Yamuna, B., & Girija, T. (2015). Enhanced Fully Distributed Load Rebalancing in Cloud Computing.

International Journal of Advances in Engineering and Emerging Technology, 7(10), 615-626.

[47] Priya, P., & Mercy Gnana Rani, A. (2015). An ANT Based Intelligent Routing Algorithm for MANET.

International Journal of Advances in Engineering and Emerging Technology, 7(10), 627-639.

[48] Dr.Sankarganesh, R., & Ilango, M. (2018). Simple Four-Quadrant Grid-Tie Fuzzy Logic Control Scheme

with Single-Phase DC/AC Converters. Excel International Journal of Technology, Engineering and

Management, 5(2), 36-41.

[49] Dr.Selvam, P., & Karl Marx, P.S. (2018). A New Harmonic Reduced 3-Phase Thyristor Controlled Reactor

for Static VAr Compensators. Excel International Journal of Technology, Engineering and Management,

5(2), 42-46.

[50] Loganathan, P., & Sridevi, S. (2018). Power Quality Analysis of Grid Connected Solar Power Inverter.

Excel International Journal of Technology, Engineering and Management, 5(2), 47-51.

Downloads

Published

31.08.2019

How to Cite

Ananth Vino, V. J., Patel, A., Kumar, A., Kumar, A., & Yadav, A. (2019). Preparation and Performance Analysis of CI Engine Run by Blends of Diesel and Biodiesel (Karanja Oil). International Journal of Psychosocial Rehabilitation, 23(3), 508-524. https://doi.org/10.61841/qx2bhv13